Photos

DM311 DATASHEET PDF

DM – Download as PDF File .pdf), Text File .txt) or read online. DM Datasheet, DM PDF, DM Data sheet, DM manual, DM pdf, DM, datenblatt, Electronics DM, alldatasheet, free, datasheet. DM Datasheet PDF Download – Green Mode Fairchild Power Switch, DM data sheet.

Author: Sataxe Voodoojar
Country: Seychelles
Language: English (Spanish)
Genre: Music
Published (Last): 10 August 2009
Pages: 198
PDF File Size: 18.33 Mb
ePub File Size: 9.34 Mb
ISBN: 510-7-86664-249-6
Downloads: 69740
Price: Free* [*Free Regsitration Required]
Uploader: Kezilkree

I don’t know how much the zener can handle but I won’t expect much more than 50 V, than the current through it would be too high. I did a comprehansive study on this power supply board a few years ago.

And than often the secondary CrapXons D8 which I have suitable replacements for, finally. So I think huge resistor is there to ensure slow enough charging of the Vcc cap otherwise there would be huge spike through the IC, auxiliary transformer datwsheet and to the cap. Typical operation on this power supply, it should reach and maintain 12 volts.

dm datasheet & applicatoin notes – Datasheet Archive

Than the zener is supposed to do all the work and can go short…. I have tens of them with bad datasheett only so at least for me, statistically, that is minority. Hopefully this information helps. But I don’t understand the purpose of the resistor, why have it there at all if the DM can handle up to v on Vstr? Home Today’s Posts Search. A potentiometer tied between the 1.

The Vstr resistor is a current limiter. Originally Posted by selldoor: So there should be some V drop with zener dropping it further to 20 V.

  CATHRYN CADE PDF

DM Datasheet PDF – Fairchild Semiconductor

A minimum throughput rate of KHz Is achieved while only dissipating 1. If Vcc drops to 7 volts or below, the chip turns off.

Originally Posted by Behemot: So you need to replace them all, every time. The feedback voltage pin is the inverting input to the PWM comparator with nominal input levels. Than the rest dstasheet taken down to voltage we want with zener and the IC is fed with that. And here are some drawings Attached: Included PWM controller integrates the fixed frequency oscillator, the undersuited for cost effective design of dataxheet converters. And shorted shottky diode on secondary side, I wonder if that was what killed the primary, or the other way around?

To turn on and stay on, the feedback voltage must increase to a minimum of 9 volts. It is the same board under the Sparkle brand. It istransformer will decrease leakage inductance. It is possible I get some of those FSPs too and that would be helpful in troubleshooting them. No abstract text available Text: But how come I end up with the really bad ones??? To sustain operation, it depends on the feedback voltage from transformer T2 thru diode D41 to provide Vcc voltage on pin 2 of the DM chip.

DataSheet: DM311

AsynchroSerial’ window Step 7 – Generation of driver code. But digging further it looks alright. It is notinductance. Take it as a simple static linear power supply – it is designed for some exact current; as other linear PSUs, it basicaly burns most of the power we do not want, here on the 1M resistor.

  ENTERPRISE INTEGRATION PATTERNS GREGOR HOHPE PDF

I am including rm311 photos of that power supply and the drawings I made. The Datashret datasheet specifies 20 V at 3 mA max. It used to be problem though you CAN squeeze at least 16V D10 caps in there and one or two on other rails with some effort. Previous 1 2 Starter for 10 newbie question I have tested the DM using primary ground – neg leg on Big cap.

DM311 Datasheet PDF

Do I still have to use primary ground for this? Step 7 – Generation of driver code.

Anyway, thanks for your valuable input, I see these PSUs quite a lot, but never had time to dive so much much into these tanks of shit Worked great and no more 5vsb headaches. That is under normal operation though, eatasheet the DM draws more than 3 mA than it should, there can be higher drop on it than on the resistor. Step 8 – Verification of the files. Oh my bad, I’ve been talking about Vcc…the Vstr should consume uA.

Than it should be more than 70 V. Now I don’t fix two transistor 5vsb circuits on Bestecs. The voltage on pin 2 of the DM must be above 9 volts, typically 12 volts.