Environment

KEPITAL F20-03 PDF

Kepital® F Datasheet. Acetal (POM) Copolymer. Supplied by Korea Engineering Plastics Co., Ltd. Create your free Prospector account to view this. Informationen on KEPITAL® F POM grade from Korea Engineering Plastics Co. Ltd. KEPITAL’s product range, from standard unfilled grades to specialties, is .. Shear strength of KEPITAL F at various temperatures. (ASTM D, t 3 mm, .

Author: Tuzragore Brazuru
Country: Luxembourg
Language: English (Spanish)
Genre: Video
Published (Last): 8 April 2011
Pages: 268
PDF File Size: 15.80 Mb
ePub File Size: 2.88 Mb
ISBN: 842-3-12338-668-1
Downloads: 95076
Price: Free* [*Free Regsitration Required]
Uploader: Doujind

KEPITAL® F20-03

Creep is the total strain of initial elastic deformation and plastic flow for loading time. Designing based on a dynamic structure analysis, obtained where a part is subjected to loading once, can only provide information if a part can be used without fracture under the single loading environment. M-Base explicitly points out that any decision about the application of materials must be double checked with the producer of this material.

Hardness Hardness of a plastic material is usually indicated in terms of Rockwell Hardness that measures surface pen-etration with a steel ball under specific conditions. Hardness of a plastic material is usually indicated in terms of Rockwell Hardness that measures surface pen-etration with a steel ball under specific conditions.

Appropriate injection pressure generally ranges to bar. If a material is used in a broad range of temperatures or if both plastic and metal parts are either assembled or molded together, the CLTE is very important in determining tolerance, interference, dimensional changes and in forecasting parts failure.

The maximum value where operation is still possible is called the PV limit.

Login to see your most recently viewed materials here. Temperature and soaking time have an influence on those properties. Kpital use of this information falls under the rules of our disclaimer.

Lower the cylinder temperature Check for gas vent Decrease injection speed. Those properties are determined from the stress and strain curve S-S curves that shows elastic and plastic behavior of a material under a dynamic load.

  EPSON DX7450 SCAN TO PDF

If other materials are introduced and mixed, caution is required because problems including contamination, lamination, and deterioration of physical properties arise. Screw rotational speed versus screw diameters Screw diameter 25 mm 40 mm 55 mm Screw rotational speed rpm 70 A back pressure of bar is generally appropriate. F20-0 includes all contents of this system. Finally part weight shows kepktal after the gate seal time. Tribological properties Tribological properties are highly affected by driving conditions such as pressure on the contacted surface, velocity, temperature, surface roughness etc.

Specific volume As shown in Figurethe molding shrinkage of KEPITAL results from both its high crystalline alignment in solidification and its thermal shrinkage from the molten state kepjtal the solid state as a function of temperature and pressure. However, long term properties show time dependent kepitall. Impact strength The impact strength is the energy to withstand a dynamic impact rather than static stress.

Unlike metals, most thermoplastic materials are insulators with a low thermal conductivity. When a voltage is applied to an insulator and incrementally increased, if a certain limit is exceeded, large current suddenly flows to break down its insulation, and the limiting value of such voltage is referred c20-03 as dielectric strength. High moisture in granule Decomposition by over-heating Insufficient gas vent Air entrap into cylinder Contamination.

Therefore, when designed, the fatigue properties of a material should be considered.

KEP :: for a better future

Thermoplastic materials are classified into amorphous and semi-crystalline polymers. Dielectric Strength When a voltage is applied to an insulator and incrementally increased, if a certain limit is exceeded, large current suddenly flows to break down its insulation, and the limiting value of such voltage is referred to as dielectric strength.

Engineering parts are often subjected to the fatigue by stress or strain which is applied repeatedly and periodically over a long period. Volume resistivity ASTM D is the resistance measured based on the internal current of a material alone, and it may be used to determine its applicability as an insulator.

  LA CASA DEL JUEZ BRAM STOKER PDF

Sales of plastic raw materials POM/South Korea engineering plastics/Kepital F20-03 BBK

Or if you don’t have an account with us yet, then click here to register. The fatigue property is dependant on the frequency of increasing temperature and various stresses ranges as shown in Figure The accelerated weathering equipment can have three light sources such as carbon arc, xenon lamp, and UV lamp. In mold fabrication, it is essential to previously review the dimensional precision, flow characteristics of the raw material, consistency of product and cost-effectiveness etc.

Dielectric strength measurement ASTM D of plastic is determined by dividing the voltage with a specimen thickness that incurs current when a test specimen prepared by injection molding is placed between two electrodes, and a voltage is incrementally increased from 0. TSH shows extremely low friction properties in sliding against itself even under high pressure in Figure A back pressure of bar is generally appropriate.

KEPITAL FA is reinforced to have high rigidity with electrical conductivity as to meet requirement for high mechanical strength and low tendency to creep.

Data sheets for overmetals, plastics, ceramics, and composites. The creep failure is a phenomenon in which a part strained and then eventually fractured under a constant stress for a long period. The impact kepiyal is the energy to withstand a dynamic impact rather than static stress.