His house was raided by BATF. After his arrest, Maadi-Griffin lost all ability to sell firearms, but continued to operate for a while, selling plan books and sabots. Maadigriffin Cal Rifle Plans. Last Updated on Thu, 11 Oct | Maadi Griffin 50 Cal. Maadi Cal Kit. Written, Published and Totally Owned by JNS Supply. Last Updated on Mon, 17 Jun | Maadi Griffin 50 Cal. Material carbon steel 3 /4″ square tubing, 5 7/8″ long Three slots on each side” wide, 1 ” long.
|Published (Last):||20 December 2007|
|PDF File Size:||6.33 Mb|
|ePub File Size:||4.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
After his arrest, Maadi-Griffin lost all ability to sell firearms, but continued to operate for a while, selling plan books and sabots. The back end of the trigger bar and the back end of the receiver should align up perfectly with the end of the itame handle as shown. Now, lift the bolt handle and remove the 50 cal unfired round. There are a lot of things that either needs to be repaired, or put together when youre a hriffin. This firearm is dangerous and can cause loss of Ufc.
Put the bolt cap back on the bolt, and take a new manufactured not reloaded live 50 cal round and insert it into the boltface shell holder, and insert the bolt into the receiver and push the bolt handle down. The width of the handle slot is.
Base Tube – Maadi Griffin 50 Cal Rifle Plans
Then screw the barrel locking ring to contact the receive! If there is too much difficulty milling out the “oval” throat of the receiver lube, it is possible to cut the tube in two pieces by cutting at 3 ” from the back.
Now clieck it out Push down of the sear with your thumb, and pull the trigger with your and the sear will drop Hold the sear down, release the trigger first, then release the sear. With the receiver in the vice, put locktite on griffln threads of the barrel only, not too much.
With headspace gages, and without headspace gages. That will become the pin when trimmed off.
Be sure the locking ring is all the way forward. The edges must be beveled, aligned, and then weld together and grind off grlffin a smooth finish.
The bolt handle should go down with just griffin slightest resistance with the round inserted. Before welding the collar to the channel iron, use the receiver as a plug, secure it to the channel iron to insure alignment of the collar. Check the bolt handle, up and down for that slight “feel” of resistance.
Put it into the lathe, screw on the brake, drill the. Not the cheap imported yellow tipped ones, do not use those. There are a lot of things that either needs to be repaired, or grkffin together when youre a homeowner. Checking the bold handle through out, tighten the ring with about a 50 pound force Wipe off the excess locktite. The lower part of the handle and the bipod form a three-legged carriage, which increases the stability of the weapon when firing.
Screw the locking ring up on the barret, screw the barrel into the receiver until it is just snug tight against the 50 cal. Insert the bolt and push the bolt handle down Ifyou have trouble at any stage of construction, call the Hot-Line for assistance. Post a comment Name The edges must be beveled, aligned, and then weld together and grinc off for a smooth finish.
Retrieved from ” http: It is exactly 90 degr tiolch The center of the deep notch lines up exactly with the ccetci rm. If there is too much difficulty ir. To reload the weapon, the buttstock plasn removed by turning the bolt and pulling it out, which carries the cartridge.
From remolding jobs to putting briffin furniture you can use these 5 power tools to get your stuff together. This is patterned after ihe NATO style weaver type base Store bought weaver type base maybe used, and drilled and screwed on base tube.
Maadi-Griffin 50 Cal. Rifle Plans
Woody Woodall Hutchinson Rd. The design of the Maadi-Griffin has been thoroughly tested and is fully developed. Grind off the marks that stand up. Then put the bolt, with the round in the receiver and lock the handle down. See the drawing, the line with a star at each end.
Dont forget too that youll need a few extra tools for other jobs around the house. The information is given herein to accomplish head spacing. With the sear installed, put the sear mqadi on the rod plana this position and insert it into the bar.